Getting Started with Plumber's Essentials for Bathtub Installation
Getting Started with Plumber's Essentials for Bathtub Installation
Blog Article
In this article down the page yow will discover a bunch of great material relating to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently available, the job can move rapidly; if you need to open up a wall to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the work as well as fit attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to think about utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This article will certainly help you install a brand-new bath tub in your washroom if you have currently acquired a new bathtub as well as don't need to alter the plan of your previous water system pipelines.
Your devices and also product list should comprise the following:
Getting ready for the Setup
Firstly, the sustaining frame provided with the bath ought to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the restricted accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, position the tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub till the spirit level checks out level.
To mount taps, fit the bottom of the furthest flexible tap adapter to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water system and also check all joints and new pipework for leakages as well as tighten them if required. Fill up the bath tub and likewise check the overflow outlet as well as the regular outlet for leaks.
Lastly, repair the bathroom paneling as described in the supplier's user's manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has actually been used at the very least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washers are in location between the tap and the sink. Protect the tap in place with the maker given backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet ports. The previous kind needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, leading to problems with wetness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealer can break relatively early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly offered on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very eager about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed reading my page. Sharing is nice. Who knows, you will be helping someone out. We recognize the value of reading our article about Installing A Bathtub.
Visit Homepage Report this page